BOE-B — owner’s manual

Listening Vocal Enhancer · Model VX-90. Manual as PDF.

1. What BOE-B is

Your vocal isn’t weak. It’s just dull. BOE-B listens to six seconds of your song, shows you why the vocal sounds dull, and fixes what it found with one knob.

Five causes, measured

What producers call a dull vocal (“buried”, “far away”, “doesn’t pop”) comes down to five causes. BOE-B measures each one and shows it on the typed sheet, what it found and where it is now:

The targets come from published measurements, not from taste: the lead-vocal level of rap records against their beat (3.2 dB on average across 83 Grammy-nominated rap songs), the long-term spectrum of natural speech, and engineering guides for presence, mud and air.

Dedication

BOE-B is our thank-you to everyone who buys from us, free with any SubverseLab purchase, and it is dedicated to Boe B (1970–2000), a pioneer of rap in Turkish.

2. Quick start

  1. Put BOE-B on the vocal track. To set the level against the beat, send the beat to BOE-B’s side input (sidechain); the BEAT ON SIDECHAIN lamp lights when it hears it.
  2. Press LISTEN and play the song. BOE-B listens for six seconds; a light runs over the face while it does. The knobs glide to what it found and the sheet fills in.
  3. LIFT starts at 6, the amount LISTEN found. Turn it down for less, up to 10 for more.
  4. Press EQUAL to compare with the input at the same loudness. If it only sounded better because it was louder, EQUAL shows it.
  5. Pick a MOOD if the song wants a colour, and use DRY/WET if the whole thing is too much.

LISTEN runs once per insert and the result is saved with the project: every later play and bounce uses it from the first sample. If the audio comes in 12 dB louder than what it heard (bleed before the vocal), it listens once more.

3. The front panel

ControlRange · defaultWhat it does
LISTENButtonPlays six seconds of the song, measures the five causes and sets the knobs. With the beat on the side input the level target is the beat + 3.2 dB.
LIFT0 to 10 · 6The one control: every stage at once in the proportions LISTEN found. 0 leaves the vocal untouched; 6 is what LISTEN found; 6 to 10 adds presence, air, compression and the saturated layer on top.
EQUALOn / off · offA/B against the input at the same loudness.
THROWOn / off · offSends the last word or line into a tempo-synced echo; the dry vocal is untouched. Automate it on the words you want thrown.
MOODCLEAN · PUSH · 90S · RADIO · PHONE · MEGAPHONE · CLEANThe colour of the whole channel. RADIO, PHONE and MEGAPHONE are voice effects for intros and hooks.
BODY−9 to +9 dB · 0 dBA shelf at 180 Hz: keep or thin the chest of the voice.
AIR0 to 12 dB · 0 dBMore air on top of what LISTEN found.
SPACE0 to 100 % · 0 %A slap / short room in parallel.
OUTPUT−12 to +12 dB · 0 dBLevel after the channel.
DRY/WET0 to 100 % · 100 %The whole channel (SPACE and THROW too) against the input. 0 % is the input, bit for bit.
INOn / off · onOff bypasses BOE-B.
?ButtonTyped help notes over the panel.

Double-click a knob to return it to the default of what is loaded now. Undo and redo with Cmd+Z on macOS, Ctrl+Z on Windows.

4. How it works

The chain, in order: a high-pass set by LISTEN (70 to 120 Hz); CLEAN, a mud cut eased on quiet frames so bleed between words is not pushed down further; the BODY shelf; a compressor (3:1, its strength set by LIFT and by how far the words drop); PRESENCE, a bell at 1.78 kHz plus a saturated parallel layer; AIR, a shelf at 10 kHz, or on a band-limited recording an exciter that builds the missing top octave from the one under it, followed by a de-esser; the MOOD colour; and a phrase-level rider that brings the vocal to its target against the beat.

Mud, presence and air are solved together, because every filter touches the band the others are measured against; a slow loop then checks what the tone stages achieved and corrects the difference. Without a beat on the side input, BOE-B keeps the vocal at its own long-term level.

5. Installation

BOE-B installs as an Audio Unit (AU) and a VST3 plug-in on macOS (Apple Silicon and Intel). On Windows (64-bit) it installs as a VST3 plug-in.

macOS

  1. Run the installer package (.pkg) you downloaded. It is signed with a Developer ID and notarised by Apple, so macOS opens it without any extra step.
  2. Choose what to install: the VST3 plug-in and the Audio Unit.
  3. Restart your DAW, or make it rescan its plug-in list.

Windows

  1. If Windows blocks the downloaded files: right-click the zip, choose Properties, tick Unblock, then extract.
  2. Copy the .vst3 folder to C:\Program Files\Common Files\VST3\.
  3. Rescan plug-ins in your DAW.

6. Specifications

ItemValue
FormatsmacOS 11 or later (Apple Silicon and Intel): VST3, AU · Windows (64-bit): VST3
Side inputOptional: the beat, for the level target and the BEAT ON SIDECHAIN lamp
Latency0 samples
LISTENSix seconds of the song, once per insert; saved with the project
Ceiling−1 dBFS sample peak
StateSaved with the DAW project; every control can be automated
PriceFree with any SubverseLab purchase

7. Getting BOE-B

BOE-B is free with any SubverseLab purchase: any plugin, the family or a sample pack bought on subverselab.com, now or before, puts BOE-B on your Account page, and a store code redeemed on subverselab.com/redeem does the same. The download is on subverselab.com/plugins/boeb and on your Account page. Install and open it in your DAW. Nothing to activate.

  1. Sign in on subverselab.com with the e-mail address you used at the checkout.
  2. Open your Account page, or subverselab.com/plugins/boeb, and download the macOS package or the Windows zip.
  3. Install it as described under Installation, then open it.